manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 20

Basic components

14

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever
is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26232

Free accelerator

To open the throttle without shifting into either
forward or reverse, push the free accelerator
button and move the remote control lever.

NOTE:

●

The free accelerator button can only be
used when the remote control lever is in the
neutral position.

●

After the button is pushed, the throttle be-
gins to open after the remote control lever is
moved at least 35°.

●

After using the free accelerator, return the
remote control lever to the neutral position.
The free accelerator button will return auto-

1. Remote control lever

2. Power trim and tilt switch
3. Free accelerator

4. Throttle friction adjuster

1. Neutral “ ”
2. Forward “ ”

3. Reverse “ ”

4. Shift
5. Fully closed

6. Throttle

7. Fully open

2

3

2

1

4

ZMU04569

N

1

F

7

6

2

R

3

4

4

6

5

7

5

ZMU04573

1. Fully open

2. Fully closed
3. Free accelerator

1. Fully open

2. Fully closed
3. Free accelerator

N

ZMU04576

1

3

2

1

3

2

ZMU04575

U6P213E0.book  Page 14  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands