Yamaha F250 Owner'S Manual Download Page 38

Page: 38 / 90

Basic components

EMU31630

Fuel management meter

This meter has functions of fuel flow meter, to-
tal consumption display, fuel economy dis-
play, and remaining fuel display.

NOTE:

After the main switch is first turned on, all the
displays come on as a test. After a few sec-
onds, the gauge will change to normal opera-
tion.

NOTE:

The fuel management meter shows various
kinds of information when the operator uses
the “

” (set) and “

” (mode) buttons. For

details, see the attached operation manual.

EMU26801

Warning system

CAUTION:

ECM00090

Do not continue to operate the engine if a
warning device has activated. Consult
your Yamaha dealer if the problem cannot
be located and corrected.

EMU26824

Overheat warning (twin engines)

This engine has an overheat warning device.
If the engine temperature rises too high, the
warning device will activate.
Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

If equipped with an overheat warning indi-
cator, it will light or blink.

●

The buzzer will sound.

1. Set button
2. Mode button

1. Fuel flow meter
2. Multifunction display

ZMU05438

ZMU05439

ZMU01757

ZMU04583

U6P213E0.book Page 32 Thursday, March 9, 2006 10:20 AM

Summary of Contents for F250



























































































Search results

Summary of Contents for F250

Reviews:

Related manuals for F250

Brands by name

Popular brands

Yamaha F250, Owner'S Manual

Search results

Summary of Contents for F250

Reviews:

Related manuals for F250

Brands by name

Popular brands