manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 45

Operation

39

EMU27670

Warming up engine

EMU30031

Electric start models

1.

After starting the engine, allow it to idle for
3 minutes to warm up. Failure to do so will
shorten engine life.

2.

Be sure the low oil pressure warning indi-
cator remains off after starting the en-
gine.

3.

Check for a steady flow of water from the
cooling water pilot hole.

CAUTION:

ECM01341

●

If the low oil pressure warning indicator
blinks after the engine starts, stop the
engine. Otherwise serious engine dam-
age could occur. Check the oil level and
add oil if necessary. Consult your
Yamaha dealer if the cause for the low
oil pressure warning indicator cannot be
found.

●

A continuous flow of water from the pilot
hole shows that the water pump is
pumping water through the cooling pas-
sages. If water is not flowing out of the
pilot hole at all times while the engine is
running, overheating and serious dam-
age could occur. Stop the engine and
check whether the cooling water inlet on
the lower case or the cooling water pilot
hole is blocked. Consult your Yamaha
dealer if the problem cannot be located
and corrected.

●

If the cooling passage is frozen, it may
take awhile for water to start flowing out
of the pilot hole.

EMU31730

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

CAUTION:

ECM01610

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting

ON

START

ZMU04596

START

ON

ZMU04590

U6P213E0.book  Page 39  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands