Yamaha F250 Owner'S Manual Download Page 52 | Manualshive

Page: 52 / 90

background image

Operation

46

WARNING

EWM00660

●

Place the gear shift in neutral before set-
ting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in
deeper water.

CAUTION:

ECM01490

●

If the engine speed is suddenly in-
creased when the outboard motor is par-
tially tilted up, the power trim and tilt unit
could be damaged.

●

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit
is above the surface of the water when
setting up for and cruising in shallow
water. Otherwise severe damage from
overheating can result.

EMU28185

Procedure for power trim and tilt / power
tilt models

1.

Place the remote control lever / gear shift
lever in neutral.

2.

Slightly tilt the outboard motor up to the
desired position using the power trim and
tilt switch / power tilt switch.

3.

To return the outboard motor to the nor-
mal running position, press the power
trim and tilt switch / power tilt switch and
slowly tilt the outboard motor down.

EMU28192

Cruising in other conditions

Cruising in salt water

After operating in salt water, flush the cooling
water passages with fresh water to prevent
them from becoming clogged with salt depos-
its.

NOTE:

For cooling system flushing instructions, see
page 48.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
(not available for some models) if you use the
outboard motor in turbid or muddy water con-
ditions.

N

ZMU04588

U6P213E0.book Page 46 Thursday, March 9, 2006 10:20 AM

«
...
50
51
52
53
54
...
»

Summary of Contents for F250



























































































Reviews:

No comments

Related manuals for F250

Brand: GRITAL Pages: 4

Brand: TAYO Pages: 42

Brand: Man Pages: 64

Brand: O.S. engine Pages: 29

Brand: DIMOEL Pages: 8

Brand: Cobra Pages: 15

Brand: Newland Pages: 29

Brand: Volvo Penta Pages: 36

Brand: Eastwood Pages: 20

Brand: Detroit Diesel Pages: 6

Brand: Volvo Penta Pages: 176

Brand: CERTIFIED Pages: 17

Brand: LEHR Pages: 30

Brand: Ford Pages: 46

Brand: STG-BEIKIRCH Pages: 57

Brand: Yanmar Pages: 231

Brand: Daewoo Pages: 603

Brand: Daewoo Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands