manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 36

Basic components

30

port soon if the low battery voltage warning
device has activated. For charging the bat-
tery, consult your Yamaha dealer.

EMU31610

Speed & fuel meter unit

This unit shows the boat speed and has the
functions of fuel meter, total fuel consumption
display, fuel economy display, fuel flow dis-
play, and system voltage display. If optional
sensors are connected to the unit, trip display,
water surface temperature display, depth dis-
play, and clock will be available. For the op-
tional sensor, consult your Yamaha dealer.
The speed & fuel meter unit is available in
round or square types. Check your speed &
fuel meter unit type.

ZMU05427

ZMU05428

1. Set button

2. Mode button

1. Speedometer
2. Fuel meter

3. Multifunction display

1. Set button

2. Mode button

2

1

ZMU05432

1

2

3

ZMU05433

2

1

ZMU05434

U6P213E0.book  Page 30  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands