manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 24

Basic components

18

WARNING

EWM00840

An improperly adjusted trim tab could
cause difficult steering. Always test run af-
ter the trim tab has been installed or re-
placed to be sure steering is correct. Be
sure you have tightened the bolt after ad-
justing the trim tab.

If the boat tends to veer the left (port side),
turn the trim tab rear end to the port side “A” in
the figure. If the boat tends to veer the right
(starboard side), turn the trim tab end to the
starboard side “B” in the figure.

CAUTION:

ECM00840

The trim tab also serves as an anode to
protect the engine from electrochemical
corrosion. Never paint the trim tab as it will
become ineffective as an anode.

EMU26340

Tilt support lever for power trim and 
tilt or hydro tilt model

To keep the outboard motor in the tilted up po-
sition, lock the tilt support lever to the clamp
bracket.

1. Trim tab
2. Bolt

3. Cap

U6P213E0.book  Page 18  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands