manualshive.com logo in svg

Yamaha DRCX, User Manual

The Yamaha DRCX User Manual is an essential guide for getting the most out of your device. With clear instructions and helpful tips, this manual will ensure a seamless experience. Download your free copy now from our website manualshive.com for an in-depth understanding of the Yamaha DRCX's features and functionalities.

Share
Download
background image

11-

13

11

11-5 Communication Command Description

COMMUNICA

TION WITH PC

(14)@MOVM  <pallet work position>,<speed>

Moves the robot to a specified pallet work position at a specified speed.

Pallet work position

: The pallet work position is a number used to identify each point

on a matrix, and can be from 1 to 65025 (=255 

×

 255). The

counter array variable C or counter variable D can also be used.

Speed

: The speed can be set to any level between 1 and 100. If PRM17

(Maximum program speed) is 100, then 100 will be equal to 3000
rpm (when PRM64 and PRM104=3000).

Transmission example

: @MOVM 5,100 c/r l/f .................. When a 4 

×

 3 matrix is

defined, the robot moves to the
point at "row 2, column 2" at
100% speed.

Response example 1

: OK c/r l/f

Response example 2

: NG c/r l/f ...................................... Data error. The specified pallet

work position is outside the
matrix.

23: data error

c/r l/f

c

CAUTION

Because calculation is performed on the assumption that the robot operates on a Cartesian coordinate system,
the desired motion cannot be obtained if a SCARA robot is used.

(15)@DRVD <axis>, <position (mm)>, <speed>

Moves a specified axis to a specified coordinate position.

Axis

: Specify the axis to be moved. "1" for the X-axis and "2" for the

Y-axis.

Position

: The position to be moved to is directly specified. If the robot uses

a rotary axis, the movement position units are in degrees.

Speed

: The speed can be set to any level between 1 and 100. When

PRM17 (program execution speed) is set to 100, then 100 will be
equal to 3000 rpm (when PRM64 and PRM104=3000).

Transmission example

: @DRVD 1, 150.55, 100 c/r l/f ..... Moves the X-axis to the

position at X=150.55 at 100%
speed.

Response example 1

: OK c/r l/f

Response example 2

: NG c/r l/f ...................................... The target position exceeds the

soft limit. Change the point
data or soft limit parameter.

30: soft limit over

c/r l/f

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for DRCX

























































































































































































































































































































Reviews:

No comments

Related manuals for DRCX

Canon imageRUNNER ADVANCE C9075S PRO User Manual preview
imageRUNNER ADVANCE C9075S PRO
Brand: Canon Pages: 20
D-Link DWC-2000 Cli Reference Manual preview
DWC-2000
Brand: D-Link Pages: 113
D-Link DWC-1000 Reference Manual preview
DWC-1000
Brand: D-Link Pages: 146
Samson 3711 Mounting And Operating Instructions preview
3711
Brand: Samson Pages: 20
Danfoss FP735Si Installation Manual preview
FP735Si
Brand: Danfoss Pages: 20
Danfoss CP715 Si Installation & User'S Instructions preview
CP715 Si
Brand: Danfoss Pages: 36
Fanimation BTCR9 Quick Start Manual preview
BTCR9
Brand: Fanimation Pages: 2
M2M C600 Technical Manual preview
C600
Brand: M2M Pages: 24
Icom IC-706MKII Manual preview
IC-706MKII
Brand: Icom Pages: 30
ICM Controls ICM330 Manual preview
ICM330
Brand: ICM Controls Pages: 2
ICM Controls ICM2909 Manual preview
ICM2909
Brand: ICM Controls Pages: 2
ray Super Remote Setting Up preview
Super Remote
Brand: ray Pages: 11
ICP DAS USA I-7188XA User Manual preview
I-7188XA
Brand: ICP DAS USA Pages: 166
ICP DAS USA SMS-531 User Manual preview
SMS-531
Brand: ICP DAS USA Pages: 64
ICS Tunnel Master Jr Manual preview
Tunnel Master Jr
Brand: ICS Pages: 83
ICP DAS USA PROFIBUS PROFI-2510 Quick Start preview
PROFIBUS PROFI-2510
Brand: ICP DAS USA Pages: 4
ICP DAS USA I-8213W-4G User Manual preview
I-8213W-4G
Brand: ICP DAS USA Pages: 40
National Instruments NI cRIO-9036 User Manual preview
NI cRIO-9036
Brand: National Instruments Pages: 40

Brands by name

Popular brands

Load more brands