Xerox Color C60 Series User Manual Download Page 39

Page: 39 / 258

If the fax option is installed, connect to a functioning telephone line using a standard
RJ11 cable.

Turning On the Printer

The printer has three power switches:

• The Ground Fault Interrupt Switch, located on the right side of the printer and near

the power cord. At installation and setup, make sure that this switch is in the On
position.

• The Main Power Switch, located behind the front cover door. Verify that this switch

is also in the On Position. Do not use this switch to turn the printer on and off for
general purposes.

• The Power On/Off Button, located on the right side of the top front panel. This is

the power button you will use to turn the printer on and off as workflow requires.

3-3

Xerox

Color C60/C70 Printer

User Guide

Installation and Setup

Summary of Contents for Color C60 Series



































































































































































































































































Search results

Summary of Contents for Color C60 Series

Reviews:

Related manuals for Color C60 Series

Brands by name

Popular brands

Xerox Color C60 Series, User Manual

Search results

Summary of Contents for Color C60 Series

Reviews:

Related manuals for Color C60 Series

Brands by name

Popular brands