Xerox Color C60 Series User Manual Download Page 214

Page: 214 / 258

Recommended Solution

Possible Cause

Fault Code

Remove all paper from the stacker
tray.

The finisher stacker tray is full

024-980

Remove all paper from the finisher
top tray.

The finisher top tray is full

024-981

Remove all paper from the stacker
tray and remove any other obstruc-
tions.

The finisher stacker tray lower
safety warning is on

024-982

Remove all paper from the booklet
tray.

The finisher booklet tray is full

024-983

Remove all paper from the booklet
tray.

The booklet stapler low staple
F signal is on

024-984

Remove all paper from the booklet
tray.

The booklet stapler low staple
R signal is on

024-985

Remove all paper from the tray. Set
the output tray for threefold.

The booklet folder tray is full

024-987

Check that the folder tray is correctly
attached and set.

The booklet folder tray is full

024-988

Check the staple cartridge and reset
correctly.

There is a problem with the
booklet maker stapler

024-989

Power Off/On the machine. If the er-
ror persists, contact the Customer
Support Center.

A communication error has
occurred with the Finisher

047-320

Remove and empty the waste contain-
er and reinstall.

Punch Waste Container is full
or near full

112-700

Confirm the staple position and try
to print again.

The settings for stapling are
canceled and prints the data

116-790

Confirm the punching position and
try to print again.

The settings for punching are
canceled

124-705

Confirm the folding settings and try
to print again.

The settings for folding are
canceled

124-706

Decrease the number of pages, or
cancel the stapling settings, then try
to print again.

The number of pages exceeds
the number of pages that can
be stapled

124-709

Xerox

Color C60/C70 Printer

13-42

User Guide

Standard/Booklet Maker Finisher

Summary of Contents for Color C60 Series



































































































































































































































































Search results

Summary of Contents for Color C60 Series

Reviews:

Related manuals for Color C60 Series

Brands by name

Popular brands

Xerox Color C60 Series, User Manual

Search results

Summary of Contents for Color C60 Series

Reviews:

Related manuals for Color C60 Series

Brands by name

Popular brands