Note!
Should a higher differential pressure occur beforehand, all the
filter candles (13) and the protective filter (2) must be checked
and, if necessary, cleaned or the candles are to be replaced
by new ones.
A highly contaminated protective filter is a sign of prolonged
operation with defective or clogged filter candles and thus (from
a differential pressure of 2 bar upwards) opened overflow valves.
It is imperative to check these components.
3 Check the ease of movement
of the worm gear unit (6),
the turbine (9) including gear (10) with flushing arm (4) see
Fig 18-6.
To this end the cover (5) or the screw plug must be removed. Now
check the ease of movement with a suitable spanner (on the
hexagon of the worm gear unit).
4 It is recommended to replace
the filter candles after 2
years.
5 Replace the O-rings.
It is advisable to replace all O-rings
and seals during an overhaul and when opened.
18.7.2.1 Filter candle inspection and cleaning
1 Drain the filter,
open the plug (16) then open the plug (14),
thereafter discharge oil. Do not refill the system with
drained oil because it is very dirty.
2 Remove the cover (17)
by opening the nuts, see Fig 18-6.
3 Pull the entire filter element
including flushing arm (4)
and gear (10) out of the housing with a suitable tool.
Note!
Make sure that the exposed gear (10) is not damaged.
4 Remove the cover plate (1).
5 Remove the end plate (18)
by opening the screws.
6 The filter candles (13)
and protective filter (2) can now be
removed.
7 Place the filter candles
and the protective filter in a suit-
able cleaner or diesel oil, max. soaking time 24 hours.
8 After immersing
clean them from the outside inwards us-
ing high pressure.
It must be ensured that the filter candles are cleaned at a pressure
of max. 60 bar and at a minimum distance of cleaning nozzle of
20 cm. Otherwise, damage to the mesh is possible.
To get a optimal cleaning effect it is recommended to use special
18
Lubricating Oil System
32-200052
18 - 14
WÄRTSILÄ 32
Summary of Contents for PAAE051728
