manualshive.com logo in svg

Vodavi STARPLUS Triad XTS, Installation Manual

The Vodavi STARPLUS Triad XTS installation manual is available for free download on our website. This comprehensive manual provides step-by-step instructions for setting up and using the product. Get your copy today and unlock the full potential of your Vodavi STARPLUS Triad XTS system. Download it from manualshive.com.

Share
Download
background image

Figures

iii

Figures

KSU Structure ....................................................................................................................................................... 1-4
XTS Default Card Layout for Cabinet 0 ........................................................................................................ 1-4
XTS Mounting Holes and Installation Layout ........................................................................................... 3-5
Mounting XTS Cabinet ...................................................................................................................................... 3-6
Connecting Cabinet 0 and Cabinet 1 .......................................................................................................... 3-7
Mounting Cabinets 0, 1, & 2 ............................................................................................................................ 3-8
Earth Cable between KSU and External RGU ............................................................................................ 3-9
Mounting Rack ..................................................................................................................................................... 3-11
Optional Rack ....................................................................................................................................................... 3-12
PSU Installation .................................................................................................................................................... 3-14
PCB Installation .................................................................................................................................................... 3-15
MPB, PMU, and MODU Configuration ......................................................................................................... 3-17
LMU1 Board Configuration ............................................................................................................................. 3-18
LMU2 Board Configuration ............................................................................................................................. 3-19
MISB & SIU Installation ...................................................................................................................................... 3-22
Talk Battery ............................................................................................................................................................ 3-23
LCOB Interface Board w/DTRU Installation ............................................................................................... 3-24
LCOBE & LCOBC w/DTRU4 Installation ....................................................................................................... 3-25
DIDB w/DTRU Installation ................................................................................................................................ 3-29
T1IB w/DTRU4 Module Installation ............................................................................................................... 3-33
PRIB w/DTRU4 Module Installation .............................................................................................................. 3-34
BRIB (Basic Rate Interface Board) ................................................................................................................... 3-35
VoIP Card with One VoIP Module Installed ............................................................................................... 3-36
VoIP Card - No VoIP Modules Installed ........................................................................................................ 3-37
Connection Side of VoIP Module (Closeup) .............................................................................................. 3-37
Case 1 of Clock Chain ........................................................................................................................................ 3-42
Case 2 of Clock Chain ........................................................................................................................................ 3-43
Case 3 of Clock Chain ........................................................................................................................................ 3-44
Case 4 of Clock Chain ........................................................................................................................................ 3-45
Electronic Telephone Interface Board (ETIB) ............................................................................................. 3-48
SLIB w/MSGU and DTRU Module Installation ........................................................................................... 3-54
SLIBE & SLIBC w/MSGU and DTRU4 Module Installation ...................................................................... 3-55
Digital Telephone Interface Board (DTIB) .................................................................................................. 3-58
Battery Back-Up Wiring ..................................................................................................................................... 3-59
RS-232 9-Pin Connector Cable Wiring ......................................................................................................... 3-60
External Paging Wiring ..................................................................................................................................... 3-61
Loud Bell Wiring .................................................................................................................................................. 3-61
External Switch / Alarm Wiring ...................................................................................................................... 3-62
Digital Station Jack Wiring ............................................................................................................................... 3-62
Electronic Station Wiring ................................................................................................................................. 3-63
Single Line Telephone Wiring ........................................................................................................................ 3-63
PFTU Wiring .......................................................................................................................................................... 3-64

Summary of Contents for STARPLUS Triad XTS











































































































































Reviews:

No comments

Related manuals for STARPLUS Triad XTS

Uniden 1035 Series Owner'S Manual preview
1035 Series
Brand: Uniden Pages: 28
Panasonic KX-TGD890C Operating Instructions Manual preview
KX-TGD890C
Brand: Panasonic Pages: 72
Vertical CONVERSip Edge 300 User Manual preview
CONVERSip Edge 300
Brand: Vertical Pages: 48
Telos DESKTOP DIRECTOR 2101 User Manual preview
DESKTOP DIRECTOR 2101
Brand: Telos Pages: 46
MALUX ExResistTel Repair Manual preview
ExResistTel
Brand: MALUX Pages: 16
VTech ES1210 User Manual preview
ES1210
Brand: VTech Pages: 37
DAC DA-113/HF User Manual preview
DA-113/HF
Brand: DAC Pages: 2
BCoda Coda One User Manual preview
Coda One
Brand: BCoda Pages: 7
Bittel UNOMedia5 User Manual preview
UNOMedia5
Brand: Bittel Pages: 6
Kingtel KT-9600 User Manual preview
KT-9600
Brand: Kingtel Pages: 12
AT&T EL51110 User Manual preview
EL51110
Brand: AT&T Pages: 69
Geemarc AmpliDECT 150 User Manual preview
AmpliDECT 150
Brand: Geemarc Pages: 28
Gigaset DL500a Manual preview
DL500a
Brand: Gigaset Pages: 137
Nortel Commander M7310N User Manual preview
Commander M7310N
Brand: Nortel Pages: 4
Philips TD9363 User Manual preview
TD9363
Brand: Philips Pages: 2
Philips Lifeline CarePartner 9500 Quick Start Manual preview
Lifeline CarePartner 9500
Brand: Philips Pages: 6
Philips Kala 6523 User Manual preview
Kala 6523
Brand: Philips Pages: 9
Philips Kala User Manual preview
Kala
Brand: Philips Pages: 15

Brands by name

Popular brands

Load more brands