Videofied V6000 Installation Manual Download Page 54

Page: 54 / 66

I N S T A L L A T I O N D A T A S H E E T - P R O G R A M M I N G

Parameters GPRS -

PREVIOUS

V32 Panel

EMEA SALES

2, rue Alexis de Tocqueville

92160 ANTONY

FRANCE

Hot line : +33 (0)820 846 620 / UK : 0871 951

Fax : +33 (0)3 90 20 66 36

is a Registered Trademark of RSI VIDEO TECHNOLOGIES.

Specifications subject to change without notice.

www.videofied.com

North American Headquarter

4455 White Bear Parkway, Suite 700

White Bear Lake, MN 55110

USA

Hot line : 877-206-5800

Fax : 651-762-4693

Display of the keypad

Actions and commentaries

TEST IN PROGRESS

YES = END

GPRS LEVEL :

4/5

It is not advisable to install a panel whose level is inferior to 3/5.

Wait

(this can least 3 minutes) for the test result which can be:

- a level between 1/5 and 5/5

- an error code (in this case, call you technical support)

PRESS INIT

OF THE DEVICE

Record your device one after another and continue your installation.

3. Table of GPRS error code

correspondances

During the GPRS level test,if there is an anormally an associated
code appears in place of the the reception level.

GPRS LEVEL :

ERROR XXX

Start the test again after first error. In case of GPRS error, we recommend

you continue installation by recording of detectors and devices and then come

back to the GPRS parameters or the GPRS level test.

Codes

Errors

010

SIM non inserted

011

Code PIN necessary

-> The PIN code must be disactivated

012

Code PUK nécessaire

013

Default SIM card

014

SIM card busy

015

Error on SIM

016

Incorrect password

017

SIM PIN2 necessary

-> The PIN code must be disactivated

018

SIM PUK2 necessary

022

SIM not found

149 and 43

Authentification error

-> Network problem or parameters (APN, USER, ...) incorrects

107

Service data GPRS non authorised

-> SIM card unsuitable

Table of correspondance error codes

It remains to

Add user codes

Parameter the partials (if need be)

Modify the alarm codes / codes from

defaults [only if the use of RTC line of the

client]

Carry out tests

Summary of Contents for V6000



































































Search results

Summary of Contents for V6000

Reviews:

Related manuals for V6000

Brands by name

Popular brands

Videofied V6000, Installation Manual

Search results

Summary of Contents for V6000

Reviews:

Related manuals for V6000

Brands by name

Popular brands