Viconics VT8600 Series User Interface Manual Download Page 69

Page: 69 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

Y1 status

BO1 aux. out

Off

G fan status

Y2 status

Off

1/2 Test Outputs

W1 status

Off

W2/OB status

Off

TEST OUTPUTS 1/2

Note 1:

The Test Outputs screen allows manual override of specified outputs. After any output state is overridden, the command is

cancelled after 1 minute of screen inactivity (auto exit to main screen) or when page is exited.

Note 2:

Use high caution when manually enabling outputs so as to not cause damage to equipment. It is the responsibility of the

Installer or Service Contractor to maintain a safe operation environment during usage.

Note 3:

These parameters can also be changed via BACnet and the changed parameter background will turn red to indicate the

parameter’s value had been overridden. The overridden value remains even if the user exits the main screen

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands