Viconics VT8600 Series User Interface Manual Download Page 87

Page: 87 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

Address

Read Only

Wireless Device Address

Shows short address of ZigBee Pro end device

Status

Read Only

Wireless Device Status

Shows the following status of ZigBee end device:

• None

: N/A

• Closed

Door and Window Sensors

• Opened

Door and Window Sensors

• No Motion

Motion Sensor only

• Motion

Motion Sensor only

• Normal:

Water Leak Sensor only

• Leak

Water Leak Sensor only

Temperature

Read Only

Wireless Device Temperature

Displays the temperature value received from the wireless device. If the wireless
device does not support temperature measurement, this object is not displayed .

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands