Viconics VT8600 Series User Interface Manual Download Page 86

Page: 86 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

6/7 Configuration

Language

English

Units

°C

Low backlight

60 %

Night backlight

5 %

RH display

Disable

Device X

Function

None

Battery

None

Address

0xXXXX

Comm. status

Online

Status

No motion

Temperature

XX °F

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Function

Default value:

None

ZigBee Device Function

Shows status of installed ZigBee device.

None:

No status reported to Room Controller

Window:

Window sensor installed

Door:

Door sensor installed

Motion

: Device set to detect motion

Status:

Updates the BACnet status of the sensor. No action is taken by the Room

Controller.

Remove

: Removes device from Device list

Water:

Water Leak sensor installed

Choices

: None, Window, Door, Motion, Status, Remove and Water

Comm. status

Default value:

Offline

Read Only

Communication Status

Shows if device is communicating with Room Controller

Not paired

: Device not paired

Online

: Device paired and online

Offline

: Device paired but offline

Invalid

: Device was paired and Room controller detected a communication error

(selected function does not match paired sensor functionality).

Display Readings

: Nor paired, Online, Offline and Invalid

Battery

Default value:

None

Read Only

Wireless Device Battery

Shows current status of battery in wireless device.

Display Readings

: None, Normal or Low

Device X

This screen is a subset of the Ecosystems screen and shows data for each paired Zigbee device. The temperature parameter is
only visible for ZigBee devices capable of measuring temperature readings. Up to 11 Device screens can show.

NOTE

: Device X pages will only show up once devices have been paired.

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands