Viconics VT8600 Series User Interface Manual Download Page 40 | Manualshive

Page: 40 / 96

background image

40

Viconics Technologies Inc.

www.viconics.com

|

[email protected]

|

Tel: (514) 321-5660

|

Fax: (514) 321-4150

028-0427-11

October 2018

CONFIGURATION 7/11

7/11 Configuration

Min fresh air

Econo min pos

0 %

Max CO2

Min CO2

Max fresh air

100 %

800 ppm

0 CFM

Econo max pos

0 CFM

1200 ppm

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Econo min pos

Default value

: 0%

Economizer Minimum Position

Minimum Outside Air damper position when Room Controller is in Occupied, Standby
or Override mode and Fan status is ON. If Room Controller is in Unoccupied mode
and/or the Fan is Off, Outside Air damper position goes to 0%.

Range:

0% to 100%

Econo max pos

Default value:

100%

Economizer Maximum Position

Maximum Outside Air damper position when Room Controller is in Occupied,
Standby or Override mode and Fan status is ON. This is valid only for Economizer,
CO

2

and Airflow functions.

Range:

0% to 100%

«
...
38
39
40
41
42
...
»

Summary of Contents for VT8600 Series

































































































Reviews:

No comments

Related manuals for VT8600 Series

Brand: Waterwise Pages: 12

Brand: Panasonic Pages: 14

Brand: Panasonic Pages: 12

Brand: Bionaire Pages: 2

Brand: Amcor Pages: 23

MULTI INV 183 E

Brand: Ducasa Pages: 8

Brand: Kaysun Pages: 64

Brand: Amana Pages: 44

Brand: Goodman Pages: 48

Brand: Kinghome Pages: 44

Cooline CDL Series

Brand: Zamil Pages: 20

Brand: MasterCool Pages: 2

Brand: Heiko Pages: 52

Brand: UFESA Pages: 36

Brand: Friedrich Pages: 23

Brand: Olimpia splendid Pages: 52

Brand: Winix Pages: 84

Brand: Oemtools Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands