Viconics VT8600 Series User Interface Manual Download Page 24

Page: 24 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

Modbus Network Settings

Modbus network screen shows when Modbus is selected in wired protocol parameter.

1/1 Modbus Network

Parity

None

Network units

Baud rate

19200

COM address

254

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Comm address

Default value:

254

Communication Address

Valid address range is set at 1 to 247 and each Modbus device must have a unique
address. Other values not recommended for Modbus.

Default value of 254 disables Modbus communication for the Room Controller.

Range

: 0 to 254

Network units

Default value:

Measurement Units

Network units transmitted over the BACnet network.

NOTE:

Use the Temperature scale parameter to change the display units locally on

the Room Controller.

Imperial

: network units shown as Imperial units.

: network units shown as International Metric units.

Choices

: Imperial or SI

Baud rate

Default value:

19200

Modbus Baud Rate

Automatically detects Modbus baud rate.

Choices

: 57600, 38400, 19200, 9600, and 4800

Parity

Default value:

Even

Parity

Determines how the parity bit of the character’s data frame is set to detect any errors
in the sent/receives frame.

Choices

: None, Odd and Even

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands