Viconics VT8600 Series User Interface Manual Download Page 38 | Manualshive

Page: 38 / 96

background image

38

Viconics Technologies Inc.

www.viconics.com

|

[email protected]

|

Tel: (514) 321-5660

|

Fax: (514) 321-4150

028-0427-11

October 2018

6/11 Configuration

Discharge HL

Cool lockout

Heat lockout

120 °F

FA range

SH lockout

Discharge LL

-40.0 °F

120 °F

45 °F

32 °F

0 CFM

CONFIGURATION 6/11

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Heat lockout

Default value:

120°F (49°C)

Heating Lockout from Outside Air Temperature

Disables mechanical heating operation when Outdoor Temperature is higher than
the “Heating Lockout” value. The Outdoor Temperature value could be received from
a sensor connected directly to the Room Controller (UI23) or via a BACnet front end
(network).

Range:

-15°F to 120°F (-26°C to 49°C)

Cool lockout

Default value:

-40°F (-40°C)

Cooling Lockout from Outside Air Temperature

Disables mechanical cooling operation when Outdoor Temperature is lower than
the “Cool Lockout” value. The Outdoor Temperature value could be received from a
sensor connected directly to the Room Controller (UI23) or via a BACnet front end
(network). The Economizer functionality (Free-cooling) can still be enabled during the
Cooling Lockout.

Range:

-40°F to 95°F (-40°C to 35°C)

Discharge HL

Default value:

120°F (49°C)

Discharge High Limit

Discharge air high temperature value at which the heating stages get locked out.

Range:

70°F to 150°F (21°C to 65°C)

Discharge LL

Default value:

45°F (7°C)

Discharge Low Limit

Discharge air low temperature value at which the cooling stages get locked out.

Range:

35°F to 65°F (2.0°C to 19.0°C)

«
...
36
37
38
39
40
...
»

Summary of Contents for VT8600 Series

































































































Reviews:

No comments

Related manuals for VT8600 Series

Brand: Haier Pages: 22

Brand: Haier Group Pages: 28

Brand: Panasonic Pages: 145

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 56

Fresh Control SAP0950WH

Brand: Sunbeam Pages: 7

Brand: Guzzanti Pages: 140

Brand: Taurus Pages: 48

Brand: Sakura Pages: 20

AWAU-YKD009-H11

Brand: Airwell Pages: 80

Brand: koppel Pages: 56

Platinum 3D Inverter Series

Brand: TECO Pages: 20

Brand: nedis Pages: 16

Brand: Daikin Pages: 14

Brand: Daikin Pages: 32

Brand: TATA Motors Pages: 32

Brand: oneConcept Pages: 26

V-Design HCNI 262 ZA

Brand: Hokkaido Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands