Viconics VT8600 Series User Interface Manual Download Page 44 | Manualshive

Page: 44 / 96

background image

44

Viconics Technologies Inc.

www.viconics.com

|

[email protected]

|

Tel: (514) 321-5660

|

Fax: (514) 321-4150

028-0427-11

October 2018

Comf. or econ.

Default value:

Comfort

Comfort or Economy Mode

Sets the operation and interaction mode of the heat pump with the auxiliary heat.

Comfort mode

: In Heating mode, if the heat pump is not able to satisfy the heating

setpoint, the auxiliary heat gets energized to satisfy the same heating setpoint.

Economy mode

: In Heating mode, if the heat pump is not able to satisfy the heating

setpoint, the auxiliary heat gets energized to satisfy only when the temperature drops
2.0°F (1.1°C) below the heating setpoint. Selecting economy mode adds a deadband
between the heat pump & auxiliary heat in heating mode. The actual temperature
maintained will be lower than the true heating setpoint to maximize the heat pump
operation. When the outdoor air temperature drops below the low balance point, the
deadband gets eliminated and the auxiliary heat maintains the true heating setpoint
alone.

Choices:

Comfort or Economy

Rev. valve

Default value:

O

Reversing Valve Operation

Heat pump reversing valve operation

O

: energize valve in cooling operation

B

: energize valve in heating operation

Choices:

O or B

Comp. interlock

Default value:

Off

Compressor Auxiliary Interlock

Sets the operation and interaction mode of the heat pump with the auxiliary heat.

Off

: In Heating mode, if the heat pump is not able to satisfy the heating setpoint,

the auxiliary heat gets energized at the same time as the heat pump stage. Typically
applies when the air handler heat pump coil is installed before the auxiliary heat (all
electric systems).

On

: In Heating mode, if the heat pump is not able to satisfy the heating setpoint, the

auxiliary heat gets energized and the heat pump is cut off. Typically applies when the
air handler heat pump coil is installed after the auxiliary heat (add on systems) There
is a 2 minute delay to restart the heat pump when the auxiliary heat is shut down.

Choices:

Off or On

«
...
42
43
44
45
46
...
»

Summary of Contents for VT8600 Series

































































































Reviews:

No comments

Related manuals for VT8600 Series

Brand: Mesa Living Pages: 37

Brand: Daikin Pages: 44

M thermal Mono Series

Brand: Midea Pages: 80

EPFX HEPA375VSC

Brand: EnviroPureFX Pages: 4

Brand: Kaysun Pages: 12

Brand: Daikin Pages: 8

Brand: Danby Pages: 40

Brand: Seifert Pages: 21

Brand: Shinco Pages: 16

Brand: Daikin Pages: 140

Brand: TCL Pages: 12

Brand: Orava Pages: 115

Brand: KYODO Pages: 10

Brand: Daikin Pages: 56

Brand: Daikin Pages: 60

Brand: Daikin Pages: 60

Brand: Daikin Pages: 24

Inverter R32 Series

Brand: Panasonic Pages: 259

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands