Viconics VT8600 Series User Interface Manual Download Page 47

Page: 47 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

11/11 Reinitialization

Push to accept:

Are you sure?

Erase all?

CONFIGURATION 11/11

PARAMETER DETAILS

Configuration parameters default value

Significance and adjustments

Erase all?

Default value:

Erase All

Accepting Yes for both and then tapping ‘Push to accept’ returns all values to the
factory default settings with the exception of the following:

•  COM address
•  Network Units
•  Network Language
•  Baud Rate
•  BACnet Instance
•  Device Name
•  Screen Contrast
•  Lua Script

Note:

Node type in ZigBee Pro menu returns to default value (Router).

Are you sure?

Default value:

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands