Viconics VT8600 Series User Interface Manual Download Page 79

Page: 79 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

6/7 Configuration

Language

English

Units

°C

Low backlight

60 %

Night backlight

5 %

RH display

Disable

ADR

Permission

Off

Shed status

Off

Shed demand

Off

Shed offset

4 °F

Shed override

Off

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Permission

Default value:

Off

Automatic Demand Response Permission

Used to permit the ADR to be applicable or not to change the Room Controller
setpoints setting or not.

Off:

The Load Shedding Demand will not be permitted.

: The Load Shedding Demand will be permitted.

Choices

: On or Off

Shed status

Default value:

Off

Read Only

Load Shedding Status

Displays the status of the Load Shedding Demand, whether it is active (On) or not
(Off). The Load Shedding status is On when the Permission is On, Shed demand is
On, and the Shed Override is Off.

Off

: Load Shedding Demand is not activated.

: Load Shedding Demand is activated.

Display Readings

: On or Off

Shed demand

Default value:

Off

Read Only

Load Shedding Demand

Sets the request to initiate Load Shedding. This demand can only be set through
BACnet by the local Utility company.

Off:

No Load Shedding Demand is received or the Shedding demand is disabled.

On:

Received the Load Shedding Demand or received the signal to activate Load

shedding.

Display Readings

: On or Off

Automatic Demand Response (ADR)

Automatic Demand Response (ADR) feature is used to reduce energy load when electric grid contingencies threaten supply-
demand balance.

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands