Viconics VT8600 Series User Interface Manual Download Page 88

Page: 88 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

6/7 Configuration

Language

English

Units

°C

Low backlight

60 %

Night backlight

5 %

RH display

Disable

Device Green Power

Function

None

Battery

None

Address

0xXXXX

Comm. status

Off

Temperature

XX °F

PARAMETER DETAILS

Configuration Parameters Default Value

Significance and Adjustments

Function

Default value:

None

ZigBee Device Function

Shows presence of installed ZigBee Green Power device. Only 1 ZigBee Green
Power device can be paired to each Room Controller.

None:

No device paired to Room Controller

Remove:

Removes device from Device Green Power group

T, rH:

Temperature and Humidity sensor paired to Room Controller

T, rH, CO

: CO

sensor paired to Room Controller

Choices:

None, Remove, T, rH or T, rH, CO

Comm. status

Default value:

Off

Read only

Communication Status

Shows communication statues between Room Controller and ZigBee Green Power
device.

Not paired

: Room Controller is not paired with any wireless ZigBee Green Power

device.

Online

: Shows Room Controller is communicating with wireless ZigBee Green Power

device.

Invalid

: Room Controller is communicating with device not using ZigBee Green Power

protocol.

Offline

: Shows Room Controller is not communicating with wireless ZigBee Green

Power device.

Paired

: Room Controller is paired with wireless ZigBee Green Power device but there

is no wireless communication between the Room Controller of the device.

Display Status

: Not paired, Online, Invalid, Offline and Paired

Device Green Power

This screen is a subset of the Ecosystems screen and shows data for a paired Zigbee Green Power device. The temperature
parameter is only visible for ZigBee devices capable of measuring temperature readings.

NOTE:

This screen is only visible when the Room Controller is paired with a ZigBee Green Power device.

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands