Viconics VT8600 Series User Interface Manual Download Page 60

Page: 60 / 96

Viconics Technologies Inc.

www.viconics.com

[email protected]

Tel: (514) 321-5660

Fax: (514) 321-4150

028-0427-11

October 2018

2/9 Service View

PI heat demand

PI cool demand

Heat dem. limit

0.0%

Cool dem. limit

Effective occ.

Occupied

Econo. demand

0.0%

SERVICE VIEW 2/9

PARAMETER DETAILS

Configuration parameters Default Value

Significance and Adjustments

Effective occ.

Read Only

Effective Occupancy

Shows as occupied, unoccupied, standby or override.

Display Readings

: Occupied, Unoccupied, Override and Standby

PI cool demand

Read Only

Cooling Demand

Display Readings

: 0-100%

PI heat demand

Read Only

Heat Demand

Display Readings

: 0-100%

Cool dem. limit

Read Only

Outdoor Temperature

Display Readings

: 0-100%

Heat dem. limit

Read Only

Supply Temperature

Display Readings

: 0-100%

Econo. demand

Read Only

Supply Temperature

Display Readings

: 0-100%

Summary of Contents for VT8600 Series

































































































Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands

Viconics VT8600 Series, User Interface Manual

Search results

Summary of Contents for VT8600 Series

Reviews:

Related manuals for VT8600 Series

Brands by name

Popular brands