Unify OpenScape 35 G HFA User Manual Download Page 104

Page: 104 / 127

104

Individual phone configuration

Adjusting audio settings

The ringer mode "HiPath" is set. The OpenScape Business sends the ring tone
type and the ring tone setting to your telephone.

Optimize the audio settings on your OpenScape Desk Phone IP 35 G for your
work environment and according to your personal requirements.

Adjusting the receiving volume during a call

You are conducting a call.

Vol.+

Vol.-

Raise or lower the volume. Keep pressing the key until the desired volume is set.

Save.

Adjusting the ring volume

Vol.+

Vol.-

Press one of the keys shown in idle mode

Page 16.

Confirm the option shown.

Vol.+

Vol.-

Raise or lower the volume. Keep pressing the key until the desired volume is set.

Save.

Adjusting the ringer pitch

Vol.+

Vol.-

Press one of the keys shown in idle mode

Page 16.

Select and confirm the option shown.

Vol.+

Vol.-

To adjust the ringer pitch: Keep pressing the keys until the desired pitch is set.

Save.

Adjusting the attention ring volume

If you are part of a team with trunk keys, other calls can be signaled acoustically
in the team during a call. You will hear the attention ring.

Vol.+

Vol.-

Press one of the keys shown in idle mode

Page 16.

Select and confirm the option shown.

Vol.+

Vol.-

Raise or lower the volume. Keep pressing the key until the desired volume is set.

Save.

Ring volume?

Ring tone?

Attention Ring Vol.

Summary of Contents for OpenScape 35 G HFA
































































































































Search results

Summary of Contents for OpenScape 35 G HFA

Reviews:

Related manuals for OpenScape 35 G HFA

Brands by name

Popular brands

Unify OpenScape 35 G HFA, User Manual

Search results

Summary of Contents for OpenScape 35 G HFA

Reviews:

Related manuals for OpenScape 35 G HFA

Brands by name

Popular brands