manualshive.com logo in svg

Tripp Lite NGI-S08C2POE8, Owner'S Manual

Share
Download
Tripp Lite NGI-S08C2POE8 Owner'S Manual Download Page 78

 

78 

 

5.2.3.

 

ONVIF 

ONVIF is an open industry forum that provides and promotes standardized interfaces for 

effective interoperability of IP-based physical security products. 

The Switch use ONVIF to discovery if there is ONVIF device connected to the Switch. 

 

ONVIF settings and ONVIF Neighbor 

The page show the detail information about ONVIF settings and ONVIF devices connected to 

the Switch. The Switch displays ONVIF devices up to total port count, NGI-S08C2POE8 

shows upto 10 ONVIF devices connected to it. If one or more ONVIF devices are connected to 

the same port it displays the last ONVIF device gets connect to it. 

 

5.2.3.1.

 

CLI Configuration 

Node 

Command 

Description 

enable 

show onvif 

This command displays the ONVIF configurations. 

enable 

configure terminal 

This command changes the node to configure node. 

config 

onvif enable 

This command enables the ONVIF on the Switch. 

config 

no onvif enable 

This command disables the ONVIF on the Switch. 

config 

onvif tx-interval  

<6-3600> 

This command configures the tx interval for the ONVIF. 

config 

no onvif tx-interval 

This command reset the tx interval to default for the 

ONVIF.(Default: 6 seconds). 

 

Summary of Contents for NGI-S08C2POE8






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands