Tripp Lite NGI-S08C2POE8 Owner'S Manual Download Page 110

Page: 110 / 157

110

6.5.

Storm Control

6.5.1.

Alarm Threshold

When the selected packet rate is over the alarm threshold, the Switch will send syslog alarm to

syslog server.

6.5.1.1.

CLI Configuration

Node

Command

Description

enable

show bandwidth-limit This command displays the current rate control

configurations.

enable

configure terminal

This command changes the node to configure node.

configure bandwidth-limit

egress <0-62500>

ports PORTLISTS

This command enables the bandwidth limit for outgoing

packets and set the limitation.

configure no bandwidth-limit

egress ports

PORTLISTS

This command disables the bandwidth limit for

outgoing packets.

configure bandwidth-limit

ingress <0-62500>

ports PORTLISTS

This command enables the bandwidth limit for

incoming packets and set the limitation.

configure no bandwidth-limit

ingress ports

PORTLISTS

This command disables the bandwidth limit for

incoming packets.

Summary of Contents for NGI-S08C2POE8






























































































































































Search results

Summary of Contents for NGI-S08C2POE8

Reviews:

Related manuals for NGI-S08C2POE8

Brands by name

Popular brands

Tripp Lite NGI-S08C2POE8, Owner'S Manual

Search results

Summary of Contents for NGI-S08C2POE8

Reviews:

Related manuals for NGI-S08C2POE8

Brands by name

Popular brands