manualshive.com logo in svg

Tripp Lite NGI-S08C2POE8, Owner'S Manual

Share
Download
Tripp Lite NGI-S08C2POE8 Owner'S Manual Download Page 135

 

135 

 

8.1.4.

 

Port Trap Event Settings 

The features allow users to enable/disables port-link-change trap notification by individual port. 

 

8.1.4.1.

 

CLI Configuration 

Node 

Command 

Description 

enable 

show snmp port-link-change-trap 

This command displays the SNMP port 

link-change trap configurations. 

enable 

configure terminal 

This command changes the node to 

configure node. 

configure  interface IFNAME 

This command enters the interface 

configure node. 

interface  snmp port-link-change-trap 

This command enables the link change trap 

on the specific port. 

interface  no snmp port-link-change-trap 

This command disables the link change 

trap on the specific port. 

config 

interface range (fastethernet1/0/ | 

gigabitethernet1/0/) PORTLISTS 

This command enters the if-range 

configure node. 

if-range 

snmp port-link-change-trap 

This command enables the link change trap 

on the specific ports. 

if-range 

no snmp port-link-change-trap 

This command disables the link change 

trap on the specific ports. 

 

8.1.4.2.

 

Web Configuration 

 

 

Parameter 

Description 

Port Link-Change Trap Settings

 

Port 

Selects the range of ports. 

State 

User can enable /disable trap events when port link change. 

Summary of Contents for NGI-S08C2POE8






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands