Toshiba nv Series Hardware Manual Download Page 95

Page: 95 / 177

Chapter 3 Installation and Wiring

6F8C1497

3.2 Before Working

Before working, always check for the following work condition and method.



Work condition

• Work in a place with less moisture and dust and no direct sunlight.

• Do not give a rapid temperature change which allows condensation to occur.

• Ensure to power off the type1 light before working.

• Use of working gloves is recommended to avoid fingers getting cut.

• Static electricity may cause breakage of electronic parts. Touch a grounded metal to

discharge static electricity from your body before working.



Tool preparation

• Please prepare a #2 Phillips screwdriver having a shaft length of 150 mm or more in

order to tighten and loosen the screw for attaching the module or the top bracket.



Work method

• Do not touch except the portions necessary for the work.

• Be careful not to lose the removed screws. Do not drop them inside the type1 light

modules, the units, or the housing case.

• In case of an error or failure, consult with our service representative.

• Printed circuit boards have sharp pointed parts. Prevent injury to your hands.

• When using drivers for connecting connectors or mounting modules and units,

ensure to use a driver suitable to the screw. A driver unsuitable to the screw is

unstable in the cross recess due to a gap. Forcibly using an unsuitable driver to the

screw does not transmit force well, causing the cross recess to strip.

Figure 3-1 Caution in using driver

Caution

(1) Never disassemble modules, units, and adapters.

Otherwise, this can go out of order.

(2) Ensure to work with the T series migration system

powered off. There is a danger of burnout or electric
shock.

Prohibited

Summary of Contents for nv Series


















































































































































































Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands

Toshiba nv Series, Hardware Manual

Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands