Toshiba nv Series Hardware Manual Download Page 117

Page: 117 / 177

Chapter 3 Installation and Wiring

6F8C1497

3.10 Input/Output Wiring

Notes for mounting and wiring the I/O module are covered in this section.

Refer to “Unified controller nv series type1 light Controller Unit User’s Manual - Basic

Hardware -” (6F8C1497) for details of I/O wiring of G2 I/O and G3 I/O.

Ground the unit.

Failure to do so may cause electric shock or fire.

Turn off the power before wiring cables.

Failure to do so may cause electric shock or system
failure.

Use sheathed crimp-type terminals for wiring
modules.

Failure to do so may cause electric shock due to exposed
conductors.

Connect an external power supply suitable for the
rating.

Failure to do so may cause explosion or fire.

A qualified electrician shall be assigned to wiring
work.

Improper wiring may cause fire, electric shock or
system failure.

◆

Important

• Make necessary wirings and connections.

For wiring with cables, be sure to use sheathed crimp-type terminals.

• Close the terminal block cover of the I/O module after confirming that all wirings and

connections are correct and firm.

Important

• Do not connect anything to the NC terminals.

Warning

Caution

Instruction

Ground

Summary of Contents for nv Series


















































































































































































Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands

Toshiba nv Series, Hardware Manual

Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands