manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 130

 

Unified  Controller  nv  Series  type1  light  Controller  Unit  Operating  Instructions 

111 

 

 5.2  Confirmation of Failure 

Check the status display LED or nV-Tool log for the failure in the T series migration system 

for type1 light controller module PUM12. 

■

 Check the status display LED of the controller module 

The FLT LED on the front panel of the controller module lights or blinks if an error occurs in 

the controller. Check the error. 

For details, refer to Table 7-1 in “Unified controller nv series type1 light Controller Unit 

User’s Manual - Basic Hardware -” (6F8C1497). 

 

■

 Check the nV-Tool error log. 

Display the error log on nV-Tool to check the detail of error and remove the cause of error. 

For details, refer to “Unified controller nv series type1 light Controller Unit User’s Manual - 

Basic Hardware -” (6F8C1497). 

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands