Toshiba nv Series Hardware Manual Download Page 15

Page: 15 / 177

Unified Controller nv Series type1 light Controller Unit Operating Instructions

xiii

This manual consists of the following chapters:

Chapter 1: Overview of T Series Migration

Describes the overview of T series migration and notes on migration.

Chapter 2: System Migration Procedures.

Describes the procedures to migrate from T2 series, S2E/S2T and T3* series
systems.

Chapter 3: Installation and Wiring

Describes the detail of installing and operating the system including installation
conditions, installation and wiring.

Chapter 4: Start and Stop

Describes how to start and stop the controller unit.

Chapter 5: Troubleshooting

Describes troubleshooting information such as measures to take when a failure or
error occurs.

Chapter 6: Maintenance and Inspection

Describes the daily and periodic inspections, including inspection methods and
replacement of batteries and other parts.

Appendix A: Base unit BUM7B

Describes the specification and usage of BUM7B and registration of tools.

Appendix B: Terminal block signal conversion adapter

Describes the part name and wiring specification of the terminal block signal
conversion adapter.

Also refer to the following manuals:

• Unified controller nv series type1 light Controller Unit User’s Manual - Basic Hardware -

6F8C1497

• Unified controller nv series type1 light Controller Unit User’s Manual -Function-

6F8C1498

• Unified controller nv series /V series Engineering Tool4 -Set Up-

6F8C1291

• Unified controller nv series/V series Engineering Tool4 -BASIC-

6F8C1290

• Unified controller nv series/V series Programming Instructions (LD/FBD/SFC/ST)

6F8C1226

• Unified controller nv series type1 light T series Migration Guide (new)

6F8C1497

• G2 I/O Adapter (GA922) Module Instruction Manual

6F8C1516

・

G3I/O

アダプタ

(GA932

※

)

モジュール

取扱説明書

6E8C5606

Summary of Contents for nv Series


















































































































































































Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands

Toshiba nv Series, Hardware Manual

Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands