manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 106

 

Unified Controller nv Series type1 light Controller Unit Operating Instructions

 

87 

■

 Procedure to mount modules to base unit BUM7B 

(1) Mount base unit BUM7B to the vertical plane of the control panel (refer to “3.5 Mounting 

Base Unit”). 

(2) Check the mounting slot on the base unit for each module. 

●

 On the main base unit: 

• Power supply connector cover (attached to BUM7B): Leftmost slot 
• type1 light controller module (PUM12): Slot S0 
• G2 I/O module: Any slot from S1 to S10 
• Space module (SP600): Any slot from S1 to S11 without containing G2 I/O 

●

 On the remote base unit: 

• Power supply connector cover (attached to BUM7B): Leftmost slot 
• TC-net I/O loop G2 I/O adapter module (GA922): Slot S0 
• G2 I/O module: Any slot from S1 to S11 
• Space module (SP600): Any slot from S1 to S11 without containing G2 I/O 
 
 

(3) Align the module to the top and bottom slot 

guides on the base unit. 

 
 
 
 
 
 
 
 
 
 
(4) Hold the module firmly and slowly push it 

straight into the slot. 

Make sure the top and bottom lock levers are 
set on the base unit and a clicking sound is 
heard. 

 
 
 
 
 
 

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands