manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 91

Chapter 3 Installation and Wiring

 

6F8C1497 

72

 

Caution

 

Mount the power supply module, the controller module,   
the station bus module, the I/O module , the interface 
module and the terminal block signal conversion adapter 
to the base unit 

Otherwise, it may cause electric shock, injury, or failure. 
Do not use them by themselves for other purposes. 

 

Caution

 

Turn power off before installing and removing the 
modules, the base unit, the terminal blocks or the 
terminal block signal conversion adapter 

Otherwise, it may cause electric shock, malfunction, or failure. 

 

Caution

 

Avoid foreign debris like wire scraps entering the 
modules , units or the terminal block signal conversion 
adapter 

These may cause fire, failure, or malfunction. 

 

Caution

 

When connecting a connector or cable and mounting a 
module to the base unit, push it in until it clicks and 
screw it firmly 

Insufficient screwing can cause failure or malfunction due to 
vibrations. 

 

Caution

 

When handling the base unit, wear the gloves. 
There is danger of injury by the end of the metal frame.

 

 

 

 

 

 

 

 

Instruction

Prohibited

Instruction

Instruction

Instruction

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands