manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 11

 

Unified Controller nv Series type1 light Controller Unit Operating Instructions 

ix 

 

  Restrictions on Application 

  This product is not developed and manufactured for use in systems including devices fatal to 

humans (Note 1),   

and thus must not be used for such purposes. 

  If you intend to use this product in a system including devices that significantly affect human safety or 

maintenance of public functions (Note 2), special consideration (Note 3) is required in system 

operation, maintenance, and management. In this case,   

please consult with our sales representative. 

(Note 1)  Devices that are directly related to human lives includes the following: 

•  Medical devices such as life-support devices and devices for surgical units 

(Note 2)  Systems including devices that significantly affect human safety or maintenance of public 

functions include the followings. 

•  Main control system of a nuclear power plant, the safety and protection system of a 

nuclear power facility, and other lines and systems important to safety 

•  Operation control systems of mass transportation system and air traffic control 

systems 

(Note 3)  Special consideration means to build a safety system (foolproof design, fail safe design, 

redundancy design, etc.) in full consultation with Toshiba's engineers. 

 
 

 Disclaimer 

  Toshiba is not liable for any loss caused by earthquake, thunder, wind, flood, fire not our 

responsibility, action by a third party, other accidents, customer's intention or negligence, incorrect 

use, or use under abnormal condition. 

  Toshiba shall not be responsible for any incidental damage (loss of business profits, interruption of 

business, change/loss of data on memory, etc.) caused by use of or inability to use this product. 

  Toshiba shall not be responsible for any damage caused by operation performed against any 

instructions stated in the instruction manual. 

  Toshiba shall not be responsible for any damage caused by malfunctions due to combination with 

the connected devices. 

  Toshiba shall not be responsible for any damage caused by malfunctions due to combination with an 

application program created by the customer. 

 

 

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands