manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 115

Chapter 3 Installation and Wiring

 

6F8C1497 

96

• While keeping the terminal conversion cable in the BUM7B space, align the upper part 

of the terminal signal conversion adapter with the top bracket of BUM7B so that the 

upper BUM7B mounting hole of the terminal block signal conversion adapter is align 

with the hole on the top bracket for securing the terminal block signal conversion 

adapter, and set and temporarily tighten the mounting screw. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Adjust the mounting position of the terminal block signal conversion adapter, and firmly 

tighten the screws at the top and bottom brackets of BUM7B to secure the adapter to 

BUM7B. 

 

(5) Connect the G3 I/O terminal block to the terminal block signal conversion adapter. 

Connect the removable terminal block of G3 I/O to the terminal block signal conversion 

adapter by aligning the direction of PCB on the adapter for mounting G3 I/O and the G3 

I/O terminal block. There is a correct combination of terminal block signal conversion 

adapter and G3 I/O terminal block. An incorrect combination may cause abnormal 

operation, system failure, breakage, fuming or ignition. 

For details of cable and adapter combination, refer to Appendix B Terminal Block Signal 

Conversion Adapter. 

 

■

 Procedure to dismount the terminal block signal conversion adapter 

Be sure to turn off the power to the T series migration system before dismounting the 

terminal block signal conversion adapter. 

Dismount the terminal block signal conversion adapter in the reverse order of mounting. 

(1) Disconnect the G3 I/O terminal block from the terminal block signal conversion adapter. 
(2) Dismount the terminal block signal conversion adapter from BUM7B. 
(3) Disconnect the attached terminal conversion cable from G2 I/O. 
(4) Disconnect the attached terminal conversion cable from the terminal block signal 

conversion adapter. 

(5) Dismount the G2 I/O module from BUM7B. 

Refer to 3.7 Mounting / Dismounting Modules. 

Top bracket 

Bottom bracket 

BUM7B mounting screw

Side view

Front view 

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands