Toshiba nv Series Hardware Manual Download Page 33

Page: 33 / 177

Chapter 1 Overview of T Series Migration

6F8C1497

1.4.5 TC-net

I/O

Adapter

Module

The G2 I/O adapter module (GA922) is used for T series migration systems. It is

mounted in the specified slot of the relevant base unit. The G2 I/O can be used as a

remote station of PUM12 in the TC-net I/O adapter modules.

(1) G2 I/O adapter module (GA922)

Refer to “Unified controller nv series G2 I/O Adapter (GA922) Module Instruction Manual”

(6F8C1516) for the appearance and specification of G2 I/O adapter module.

A basic unit of remote station can be configured by mounting GA922 in slot S0 of the

base unit (BU668

、

BU666

、

BU664) for unified controller type 1 light.

A remote unit can be configured by mounting GA922 in slot S0 of the base unit (BUM7B)

for T series migration systems. Use GA922 having a serial number xx1331 or greater for

mounting on BUM7B.

Refer to “1.4.2 Base Units” for mounting G2 I/O adapter module GA922 on the base unit.

(2)G3 I/O

アダプタモジュール

(GA932)

※

Summary of Contents for nv Series


















































































































































































Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands

Toshiba nv Series, Hardware Manual

Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands