manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 134

 

Unified  Controller  nv  Series  type1  light  Controller  Unit  Operating  Instructions 

115 

 

 6.2  Periodic Inspection 

Check items periodically (about once every 6 months) on the T series migration system for 
type1 light controller module PUM12 are listed below. Also check these items when the 
surrounding or operating environment has changed: 
 

Checking items in periodical inspection: 

■

  Power supply (supply voltage) 

■

 Installation status 

Base unit 

Power supply module 

Controller module 

I/O module 

Adapter module 

Terminal block, connector 

Breakage of wiring cables 

■

  Breakage of cables 

■

 LED lighting status 

■

 Loosen terminals 

■

 Surrounding environment 

■

 Programs, etc. 

■

 Battery, etc. 

 

For details of inspection, refer to: 

·“Unified controller nv series type1 light Controller Unit User’s Manual - Basic 

Hardware -” (6F8C1497) 

･

G2 I/O Adapter (GA922) Module Instruction Manual (6F8C1516) 

 

 

 

Wear protective equipment to prevent electric shock when 
measuring the supply voltage at the power supply terminal 
during inspection. Failure to do so may cause electric 
shock. 

 

 

 

Do not modify, repair, disassemble or adjust devices, 
modules and boards. 
It may cause electric shock, fire, injury or system failure. 
When malfunction or failure is found, contact our branch 
office or service agent.

 

 

 

 

Warning 

Warning 

Prohibited 

Instruction 

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands