Toshiba nv Series Hardware Manual Download Page 54

Page: 54 / 177

T series Migration User’s Manual - Hardware -

2.2.2 Base

Unit

The type1 light base unit, relevant to the S2T/S2E base unit, is selected using the T-PDS

conversion tool.

Table 2.13 S2T/S2E base unit conversion

After conversion

Before conversion

nv controller

type1 light

BU648E

BU643D

BU668

BU666

BU664

T series

conversion
controller

S2T

BU648E

○

× × × ×

BU643D

○

× × ×

S2E

BU668

○

× ×

BU666

○

BU664

○

Expansion

BU668

× ×

○

× ×

BU666

× ×

○

BU664

× ×

○

: Selectable, ×: Not selectable

The base unit used for S2T/S2E and type1 light is the same model.

Be sure to select the same model when the base unit is converted.

Refer to the following manuals for the appearance and specification of the base unit:

･

Integrated controller model 200 series

Sequence Controller S2 User’s Manual - Basic Hardware - (6F8C0836)

S2T User’s Manual - Basic Hardware - (6F8C0936)

S2E User’s Manual - Basic Hardware - (6F8C1094)

･

Unified controller nv series

Unified controller nv series type1 light Controller Unit User’s Manual - Basic Hardware -

(6F8C1497)

Summary of Contents for nv Series


















































































































































































Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands

Toshiba nv Series, Hardware Manual

Search results

Summary of Contents for nv Series

Reviews:

Brands by name

Popular brands