manualshive.com logo in svg

Toshiba nv Series, Hardware Manual

Share
Download
Toshiba nv Series Hardware Manual Download Page 113

Chapter 3 Installation and Wiring

 

6F8C1497 

94

 

 3.8 

Mounting/Dismounting Terminal Block Signal Conversion Adapter

 

This section describes the procedure to mount and dismount the terminal block signal 

conversion adapter of the T series migration system to and from base unit BUM7B. For 

mounting and dismounting modules such as G2 I/O or G3 I/O with terminal blocks and 

connectors, refer to “Unified controller nv series type1 light Controller Unit User’s Manual - 

Basic Hardware -” (6F8C1497) or “T3/T3H User’s Manual - Hardware - ” (UM-TS03***-J002). 

 

■

 Procedure to mount the terminal block signal conversion adapter 

Be sure to turn off the power to the T series migration system before mounting the terminal 

block signal conversion adapter. 
(1) Mount the G2 I/O module to BUM7B. 

Refer to 3.7 Mounting/Dismounting Modules for mounting G2 I/O to base unit BUM7B. 

 

(2) Connect the attached terminal conversion cable to the terminal block signal conversion 

adapter. 

Connect the cable and adapter properly by aligning the cable connector on the terminal 

block signal conversion adapter and the adapter side connector of the attached terminal 

conversion cable before connection. 

• Connector type terminal conversion cable: 

Insert the connector of the terminal conversion cable completely into the terminal block 

signal conversion adapter, and tighten the screws at both sides of the connector. Check 

there is no rattling or loose part in the connector. 

• Terminal block type terminal conversion cable: 

Insert the connector of the terminal conversion cable into the terminal block signal 

conversion adapter until a clicking sound is heard. Check there is no rattling or loose part 

in the connector. 

There is a correct combination of the terminal block signal conversion adapter and 

terminal conversion cable. An incorrect combination may cause abnormal operation, 

system failure, breakage, fuming or ignition. Be sure to connect the attached terminal 

conversion cable to the terminal block signal conversion adapter. 

For details of cable and adapter combination, refer to Appendix B Terminal Block Signal 

Conversion Adapter. 

 

(3) Connect the attached terminal conversion cable to G2 I/O. 

Connect the G2 I//O side connector of the attached terminal conversion cable to G2 I/O. 

There is a correct combination of G2 I/O and terminal conversion cable. An incorrect 

combination may cause abnormal operation, system failure, breakage, fuming or ignition. 

Be sure to connect the attached terminal conversion cable to G2 I/O. 

For details of cable and adapter combination, refer to Appendix B Terminal Block Signal 

Conversion Adapter. 

 

Summary of Contents for nv Series


















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands