manualshive.com logo in svg

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 97 / 179

Share
Download
Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 97

94

1.  ACCESS  CODES

If the copier is set up so that access codes can be used, you can make copies only after entering
the access code.
When making copies using access codes, the copy quantity is stored for each access code used.
The access code is a 4-digit number, and up to 120 codes can be set.
* 0000 cannot be set as an access code.

Note: If you want to use the access codes, ask the service technician to set them.

Procedure

The following message appears:

Enter job access code

1

Key in a 4-digit access code.

2

.

The access code appears on the message
display, and the touch panel then displays the
following:

READY

Make copies as you would normally do.

.

When you have finished making copies, either
press the FUNCTION CLEAR key twice, or
wait 45 seconds. The following message
appears:

Enter job access code

3

Summary of Contents for e-STUDIO 55




















































































































































































Reviews:

No comments