Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 122

Page: 122 / 179

119

USING THE

OPTIONAL

FINISHER

Press the START key.

The copies are automatically stapled after
each set has been copied.

To add more originals, press the CONTINUE
key during the scanning.

Stapled copies exit onto the trays.

When the finisher trays reach maximum
capacity, the following message appears:

Finisher full: Remove paper

Remove the copies from the trays and
press the START key to continue.

To cancel copying, press the STOP key to
interrupt the copy run, then press the
MEMORY CLEAR key.

The number of copies you can staple at a time
is shown below.

A4, B5, : 50

A3, B4, A4-R : 30

If you set the staple mode and more than
specified number of sheets is copied, the
finisher automatically enters the sort mode.

Summary of Contents for e-STUDIO 55




















































































































































































Search results

Summary of Contents for e-STUDIO 55

Reviews:

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 122 / 179

Search results

Summary of Contents for e-STUDIO 55

Reviews: