manualshive.com logo in svg

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 131 / 179

Share
Download
Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 131

128

1

2

Adding Paper to the Front Cassette

Holding the whole ream of paper as shown,

place it in the cassette.

.

Up to 500 sheets of paper (recommended by
Toshiba) can be set.

.

Do not add paper above the limit line indicated
on the back guide.

.

Do not use creased, folded, wrinkled or damp
sheets of paper.

Pulling up the grip, pull out the cassette

slowly until it comes to a stop.

Limit line

3

Slowly push the cassette straight in until

it comes to a stop.

.

Make sure that the cassette is pushed in fully.

When the paper supply in the selected cassette or large-capacity feeder runs out, the cassette
or large-capacity feeder on the display panel flashes and this message appears:

Add paper

Add paper as described below.

1.  ADD  PAPER  SYMBOL

Summary of Contents for e-STUDIO 55




















































































































































































Reviews:

No comments