Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 14

Page: 14 / 179

DESCRIPTION

OF THE DIGITAL

COPIER

��

OPERATION GUIDE key
Pressing the INFO key
displays the appropriate
operation procedure.
Pressing this key after a
function has been set
displays the features
available.

��

MESSAGE display
Displays the status of the
copier, operation proce-
dures and various
instructions to the user in
short sentences and
graphics.

��

DIGITAL keys
Use these keys to enter
the desired copy quantity.
You can set up to 999
copies.

��

FUNCTION CLEAR key
When you press this key,
all the modes you have
selected are cleared to the
default settings.

��

STOP key
Press this key to stop a
copy run.

��

START key
Press this key to start
copying.

��

CLEAR key
Use this key to correct the
entered copy quantity.

Summary of Contents for e-STUDIO 55




















































































































































































Search results

Summary of Contents for e-STUDIO 55

Reviews:

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 14 / 179

Search results

Summary of Contents for e-STUDIO 55

Reviews: