manualshive.com logo in svg

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 55 / 179

Share
Download
Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 55

52

14.  INTERRUPT  COPYING

The interrupt Copy is a convenient feature that allows the user to pause a job that is currently
being done. This mode allows for a single copy to be made from either the bypass guide or
nominated cassette. Multiple copies are possible by pressing the START key once for every
copy required.

1

Press the INTERRUPT key.

The following message appears:

  Job interrupted job 1 saved

Replace the original with a new original.

.

After lifting the automatic document feeder,
place the original on the glass face down with
the bottom toward you and the left side
centred against the original scale.

.

Close the automatic document feeder slowly
after the original size has been detected.

.

During the interruption, the automatic
document feeder and automatic duplexer are
inoperable.

2

Select the desired copy size, exposure and

reproduction ratio.

4

3

After interrupt copying is finished, press

the INTERRUPT key again.

.

This message will appear:

  READY to resume job 1

5

Press the START key.

.

You can make multiple copies by pressing the
START key once for each copy desired.

Note: Interrupt copying is not available during

scanning of the originals. Press the
INTERRUPT key when the scanning has
completed.

INFO

COPY

PRINTER / NETWORK

Summary of Contents for e-STUDIO 55




















































































































































































Reviews:

No comments