manualshive.com logo in svg

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 51 / 179

Share
Download
Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 51

48

12.  BYPASS  COPYING

The bypass copying mode is convenient in the following instances:
• when the size of any of the paper cassettes installed in the copier is not that which you

require.

• when you want to use a special type of paper such as OHP film.

1

Place the original(s) on the original feed

tray or on the glass.

.

After aligning the edges of the originals, set
them  face up on the original feed tray and
align the slides to the edges of the originals.

Note: Remove any paper clips or staples from

originals before placing them on the
original feed tray.

Slides

.

After lifting the automatic document feeder,
place the original on the glass face down with
the bottom toward you and the left side
centred against the original scale.

2

Select the desired exposure and

reproduction ratio.

Summary of Contents for e-STUDIO 55




















































































































































































Reviews:

No comments