manualshive.com logo in svg

Toshiba e-STUDIO 55, Operator'S Manual For Copying Functions, Page: 168 / 179

Share
Download
Toshiba e-STUDIO 55 Operator'S Manual For Copying Functions Download Page 168

165

WHEN THE

GRAPHIC SYMBOLS

FLASH

When the CALL SERVICE 

 symbol flashes, the

following message appears and copying is no
longer possible:

Call for service

The telephone number of your service technician
will be displayed.
Note it down, then turn the power switch off and
immediately call service for assistance.

Note:

Since a heater is used to fix toner images to the copy paper, a safety circuit is incorporated
in this copier. After you turn on the power switch, if a certain temperature is not attained
within a certain period of time, the safety circuit assumes that something abnormal has
happened. This causes the operation of the copier to stop and flashes the CALL SERVICE

 symbol. This can possibly occur when the temperature is low even though the

copier is not malfunctioning. If this occurs, turn the power switch off and then on again.
Repeat this procedure twice and if the problem still persists, turn off the power switch
and call for service.

11.  CALL  SERVICE 

  SYMBOL

Summary of Contents for e-STUDIO 55




















































































































































































Reviews:

No comments