Thermo NanoDrop One User Manual Download Page 293

Page: 293 / 312

Maintaining Your Instrument

Instrument Diagnostics

Thermo Scientific

NanoDrop One User Guide

293

To interpret intensity check results

If one of these indicators:

• UV

• Visible

• Bias

has an adjacent yellow triangle instead of the green check marks shown above,

clean the

pedestals with deionized water

and then repeat the Intensity Check.

If a yellow triangle appears next to the Bias indicator, make sure the room is within the
temperature specifications for the instrument.

If the Intensity Check fails again,

Related Topics

• Performance Verification

• Pedestal Image Check

Performance Verification

Run Performance Verification every 6 months to confirm pathlength accuracy is within
specifications.

Supplies needed

• lint-free laboratory wipes

• deionized water (DI H

• calibrated precision pipettor (0–2 μL)

•

PV-1 performance verification solution

(liquid photometric standard available only from

us or a local distributor)

• laboratory gloves

Note

The PV-1 solution comes in a single-use ampoule. Before you open the ampoule,

shake it vigorously and then allow the liquid to collect in the bottom portion of the
ampoule. After the ampoule is opened, its contents must be used within one hour. Pipette
directly from the ampoule; do not transfer the solution.

Summary of Contents for NanoDrop One
























































































































































































































































































































Search results

Summary of Contents for NanoDrop One

Reviews:

Thermo NanoDrop One, User Manual, Page: 293 / 312

Search results

Summary of Contents for NanoDrop One

Reviews: