Thermo NanoDrop One User Manual Download Page 288

Page: 288 / 312

Maintaining Your Instrument

Decontaminating the Instrument

288

NanoDrop One User Guide

Thermo Scientific

Supplies needed

• lint-free laboratory wipes

• deionized water (DI H

• 0.5% sodium hypochlorite solution (1:10 dilution of commercial bleach, freshly

prepared)

• pipettor

NOTICE

• Do not use hydrofluoric acid (HF) on the pedestals. Fluoride ions will permanently

damage the quartz fiber optic cables.

• To prevent damage from spills, keep containers of liquids away from the instrument.

• Do not use a squirt or spray bottle on or near the instrument as liquids will flow into

the instrument and may cause permanent damage.

• Do not attempt to remove the diaphragm around the lower pedestal as it is

permanently affixed to the instrument.

• Do not allow HCl, alcohol, bleach, acetone or any other solvent to remain on the

diaphragm for more than one minute or it may loosen the seals. If the diaphragm
becomes loose,

Summary of Contents for NanoDrop One
























































































































































































































































































































Search results

Summary of Contents for NanoDrop One

Reviews:

Thermo NanoDrop One, User Manual, Page: 288 / 312

Search results

Summary of Contents for NanoDrop One

Reviews: