manualshive.com logo in svg

Thermo NanoDrop One, User Manual, Page: 284 / 312

Share
Download
Thermo NanoDrop One User Manual Download Page 284

4

  Maintaining Your Instrument

Maintaining the Pedestals

284

NanoDrop One User Guide

Thermo Scientific

Supplies needed

• lint-free laboratory wipes

• deionized  water  (DI H

2

O)

• for thorough cleaning: 

PR-1 kit

 or 

0.5M HCl

To clean the pedestals 
between measurements

Lift the instrument arm and clean the 
upper and lower pedestal with a new 
laboratory wipe.

To clean the pedestals 
between users

1. Lift the arm and clean both pedestals 

with a new laboratory wipe.

2. Pipette 3–5 μL DI H

2

O onto the 

lower pedestal.

3. Lower the arm and wait 2–3 minutes.

4. Lift the arm and clean both pedestals 

with a new wipe.

Tip

: When thorough cleaning is required 

(for example, to remove dried sample left 
on the pedestals), substitute 0.5M HCl for 
the DI H2O in the procedure above and 
follow with 3-5 μL DI H2O. You can also 

recondition the pedestals

 using PR-1 

compound.

Summary of Contents for NanoDrop One

























































































































































































































































































































Reviews:

No comments