Thermo Scientific Barnstead GenPure xCAD Plus System Operating Instructions Manual Download Page 92

Page: 92 / 128

Maintenance

Change the ultrapure cartridge

GenPure

Thermo Scientific

Open the supply of feedwater and switch the
system on again.

The Code to do this transaction please refer from
the Code table „code lock” found in chapter

“Code lock”

page 82

. You need a level one

code.

Go in the Menu to the point “change
filter cartridge” and press enter.

b. Enter new serial number of the ultrapure

cartridge in by pushing the button
nonstop or Interval to change the digits
and the UV button to go to the next
value.

When you are finished, press enter and
the new serial number is saved. You can
only use a serial number one time.

Discard at least 5 liters of water.

Step

Action

Figure

Feedwater
supply

Summary of Contents for Barnstead GenPure xCAD Plus System

































































































































Search results

Summary of Contents for Barnstead GenPure xCAD Plus System

Reviews:

Related manuals for Barnstead GenPure xCAD Plus System

Brands by name

Popular brands

Thermo Scientific Barnstead GenPure xCAD Plus System, Operating Instructions Manual

Search results

Summary of Contents for Barnstead GenPure xCAD Plus System

Reviews:

Related manuals for Barnstead GenPure xCAD Plus System

Brands by name

Popular brands